Its farming time whether its tillage, plowing, or just normal farm work. It’s a hot day, and there are lots of things to get done around the farm. However, suddenly you notice that the temperature gauge is showing higher than normal temperature reading. At this time, it’s wise to stop operating the tractor, and if the temperature level is not at its peak level on the gauge, make a quick check of the engine area to detect any leaks or other obvious problems, and then return quickly to turn the engine off.
The older tractors will not have safety shut off devices. The newer computerized controlled tractors will have audible alarms and in many cases, these controls will automatically shut the engine down when excessive temperature readings are present.
A tractor’s cooling system comprises of several components. There is a radiator, a radiator fan, water pump, lower radiator hose, upper radiator hose, a thermostat, and a liquid that flows through the engine, to the radiator where it is cooled, and then recalculated back into the engine to continue the cooling process.
The first step in diagnosing an overheating problem is to ensure that there is enough fluid in the radiator. This can be checked by looking in the overflow container. If that is filled, and there is no blockage from the radiator to the overflow container, then the engine must be allowed to cool. Once cooled, the radiator cap should be removed and the radiator checked for fluid.
If there is a fluid shortage, then the cause of the shortage needs to be identified. A damaged lower and upper radiator hose can be changed. The clamps on the system can be tightened or changed.
For fluid shortage, there should be visible leaks around the failed component, either the hoses, a leaking radiator, or broken water pump. Should there be no visible leaks and missing cooling fluid, then this can indicate a damaged cylinder head gasket that is allowing the fluid to either leak into the engine, or be pulled into the combustion chamber, burnt, and then exhausted.
The thermostat, a simple device, is located directly in the path of the flowing liquid. It contains a bi-metallic disc, that opens when immersed in fluid of a high temperature, and closes when the temperature of the fluid reduced below a predetermined level. Typically, most thermostats will fail in an open manner, thereby allowing overcooling rather that the opposite, overheating.
A simple way to test the thermostat is to put it into a container of water and bring that container to a boil on a stove, or hotplate. As the water temperature reaches boiling, the thermostat should begin to open. If it doesn’t, then it needs to be changed.
Other sections of the cooling system not discussed here are the water pump, and the radiator, gauges and radiator cooling fan systems.
Ontario Parts Hotline is a premium provider of John Deere Parts and John Deere Tractor Water Pump.
Showing posts with label Tractor Repair Tips. Show all posts
Showing posts with label Tractor Repair Tips. Show all posts
Wednesday, 23 November 2011
How To Save on DownTime on Engine Repair by Using a Long Block
Repairing an engine by a complete overhaul is a popular way of maintaining tractor engines, and ensuring continuous problem free operation of heavy duty machines. However, the overhaul process can take a minimum of five (5) days if all of the parts are readily available for the overhaul, and typically approximately ten (10) days for the complete overhaul to be completed, with the additional time to procure the parts needed for the overhaul.
Depending on what needs to be repaired on the old engine, a complete block assembly engine, or a long block as it is sometimes called, can be faster repair job for a tractor engine that requires a new block and a cylinder head.
The short block comprises of the cylinder block and the crankcase connected by a connecting rod and precision heavy duty welding. The long block is the next level in engine repair, as compared to the short block. The long block has additional components that make repairs less tedious.
The most significant addition that makes up the long block is the cylinder head. This is bolted to the top of the cylinder block by head bolts and sealed with a head gasket. Depending on the engine model and manufacturing company, the cylinder head can contain a section of the combustion chamber. All will have the intake valves, exhaust vales, valve springs, valve keepers, and the rocker arm assembly. The rocker arm assembly comprises of the rocker arm shaft, tappets, push rods, and the rocker arms. The camshaft assembly in the crankcase moves the push rods which mechanically operates the rocker arm assembly.
Both the long block and the short block will have the front gear train, with pulleys and chains. However, the long block will have the front plate, which is a protective covering for the gear train components.
In some models, the rear seal housing with the seal is provided. For example, the 6081 John Deere engine long block, this housing is provided as a part of the complete engine assembly.
The oil pump and oil pump accessories are another pertinent addition to the long block assembly. The exact location of the oil pump varies by engine type and manufacturer, however, a large percentage of oil pumps are fitted in the lower section of the crankcase, with an oil filler tube extending downwards into the area where the oil pan will be located. At the bottom of this filler tube, is fitted an oil strainer.
The long block would have been fitted internally with many gaskets, including the front gear train gasket, the oil pump gasket, the head gasket, and a few others. However, since there will be many engine accessories to be added to the external parts of the engine, a complete gasket kit is normally shipped with the engine assembly. This will include gaskets for the exhaust and intake manifolds, water pump, fuel pump and fuel transfer pumps.
For completely remanufactured engine assemblies that were rebuilt to OEM specifications, all internal components used in the rebuilt process will be new components, with the exception of the blocks, cylinder head, and crankshaft which are typically rebuilt to OEM specifications and reused.
Ontario Parts Hotline is a major supplier of John Deere Parts and John Deere Tractor Parts
Depending on what needs to be repaired on the old engine, a complete block assembly engine, or a long block as it is sometimes called, can be faster repair job for a tractor engine that requires a new block and a cylinder head.
The short block comprises of the cylinder block and the crankcase connected by a connecting rod and precision heavy duty welding. The long block is the next level in engine repair, as compared to the short block. The long block has additional components that make repairs less tedious.
The most significant addition that makes up the long block is the cylinder head. This is bolted to the top of the cylinder block by head bolts and sealed with a head gasket. Depending on the engine model and manufacturing company, the cylinder head can contain a section of the combustion chamber. All will have the intake valves, exhaust vales, valve springs, valve keepers, and the rocker arm assembly. The rocker arm assembly comprises of the rocker arm shaft, tappets, push rods, and the rocker arms. The camshaft assembly in the crankcase moves the push rods which mechanically operates the rocker arm assembly.
Both the long block and the short block will have the front gear train, with pulleys and chains. However, the long block will have the front plate, which is a protective covering for the gear train components.
In some models, the rear seal housing with the seal is provided. For example, the 6081 John Deere engine long block, this housing is provided as a part of the complete engine assembly.
The oil pump and oil pump accessories are another pertinent addition to the long block assembly. The exact location of the oil pump varies by engine type and manufacturer, however, a large percentage of oil pumps are fitted in the lower section of the crankcase, with an oil filler tube extending downwards into the area where the oil pan will be located. At the bottom of this filler tube, is fitted an oil strainer.
The long block would have been fitted internally with many gaskets, including the front gear train gasket, the oil pump gasket, the head gasket, and a few others. However, since there will be many engine accessories to be added to the external parts of the engine, a complete gasket kit is normally shipped with the engine assembly. This will include gaskets for the exhaust and intake manifolds, water pump, fuel pump and fuel transfer pumps.
For completely remanufactured engine assemblies that were rebuilt to OEM specifications, all internal components used in the rebuilt process will be new components, with the exception of the blocks, cylinder head, and crankshaft which are typically rebuilt to OEM specifications and reused.
Ontario Parts Hotline is a major supplier of John Deere Parts and John Deere Tractor Parts
What is a Short Block and How Is It Best Used
Replacement engines for tractors, combines and other heavy duty equipment are available in different configurations and types. The choice on which to choose will depend on several factors, including the damage to the present engine, and how much down time can be absorbed.
A problem that sometimes necessitates an engine block replacement arises from loose main bearings, which when spun out, can cause a broken connecting rod that violently breaks and punches through the side of the engine block. There has been examples where the connecting rod punches up into the cylinder head.
In such examples, all other engine components are in perfect working condition, however, the bottom section of the engine needs to be replaced. In engine terminology, the bottom section of the engine is called a short block. Large tractor engines are typically made up of four major components, joined together by smaller components and with accessories attached to the external areas of the engine.
The four major components of a large tractor engine are the cylinder head at the top, the cylinder block under the cylinder head, the crankcase under the cylinder block, and the oil pan at the bottom of the crankcase.
The short block engine comprises two of these, namely the cylinder block, and the crankcase. In the automotive field and lawn mower manufacturer which uses small engines, the cylinder block and the crankcase is casted as a single casting during manufacture. However, in large tractor engine and marine engine manufacture, the cylinder block and the crankcase are manufactured as separate castings and then joined afterwards by welded steels plates and precision heavy duty welding. The cylinder block and the crankcase serve different complimentary functions.
The cylinder block is the section of the engine that houses the cylinder liners, the piston assembly and the camshaft. The top section of the cylinder block is called the combustion chamber. On the top of this assembly is bolted the cylinder head. The cylinder head is not a part of the short block engine.
The bottom section of the short block engine is the crankcase. This section of the engine houses the crankshaft, main bearings, crank seals, and front gear train. The combination of the cylinder block and the crankcase is called the short engine block. The two components are welded together, and internally, are connected by the connecting rods, hence the term, "connecting" rods. Motive power is transferred from the piston movements to the crankshaft via the connecting rods.
Short engine blocks removed from salvaged tractor yards are called good used short blocks. Used engine short blocks that were totally overhauled, replaced with new or rebuilt internal components, and restored to OEM specifications are called rebuilt short blocks. OEM companies may have their own abbreviations for their engine, i.e., John Deere will refer to their reconditioned engine blocks as John Deere Reman, and Caterpillar will call theirs Cat Reman. OEM reman products typically carry the new product unlimited use warranty, when installed by the dealer's mechanics.
Ontario Parts Hotline is a major supplier of John Deere Parts and John Deere Tractor Parts
A problem that sometimes necessitates an engine block replacement arises from loose main bearings, which when spun out, can cause a broken connecting rod that violently breaks and punches through the side of the engine block. There has been examples where the connecting rod punches up into the cylinder head.
In such examples, all other engine components are in perfect working condition, however, the bottom section of the engine needs to be replaced. In engine terminology, the bottom section of the engine is called a short block. Large tractor engines are typically made up of four major components, joined together by smaller components and with accessories attached to the external areas of the engine.
The four major components of a large tractor engine are the cylinder head at the top, the cylinder block under the cylinder head, the crankcase under the cylinder block, and the oil pan at the bottom of the crankcase.
The short block engine comprises two of these, namely the cylinder block, and the crankcase. In the automotive field and lawn mower manufacturer which uses small engines, the cylinder block and the crankcase is casted as a single casting during manufacture. However, in large tractor engine and marine engine manufacture, the cylinder block and the crankcase are manufactured as separate castings and then joined afterwards by welded steels plates and precision heavy duty welding. The cylinder block and the crankcase serve different complimentary functions.
The cylinder block is the section of the engine that houses the cylinder liners, the piston assembly and the camshaft. The top section of the cylinder block is called the combustion chamber. On the top of this assembly is bolted the cylinder head. The cylinder head is not a part of the short block engine.
The bottom section of the short block engine is the crankcase. This section of the engine houses the crankshaft, main bearings, crank seals, and front gear train. The combination of the cylinder block and the crankcase is called the short engine block. The two components are welded together, and internally, are connected by the connecting rods, hence the term, "connecting" rods. Motive power is transferred from the piston movements to the crankshaft via the connecting rods.
Short engine blocks removed from salvaged tractor yards are called good used short blocks. Used engine short blocks that were totally overhauled, replaced with new or rebuilt internal components, and restored to OEM specifications are called rebuilt short blocks. OEM companies may have their own abbreviations for their engine, i.e., John Deere will refer to their reconditioned engine blocks as John Deere Reman, and Caterpillar will call theirs Cat Reman. OEM reman products typically carry the new product unlimited use warranty, when installed by the dealer's mechanics.
Ontario Parts Hotline is a major supplier of John Deere Parts and John Deere Tractor Parts
Understating Why Diesel Engines are Hard to Start in Cold Weather
Attempting to start Diesel engines in cold or sub zero temperatures is extremely difficult and usually an impossible task, unless appropriate accessories has been added to the engine to assist in such starting.
The hard starting problems of diesel engines in below zero / freezing temperatures are caused by two factors. One is the initial cold air being drawn into the turbocharger and compressed into the engine’s cylinder head. The second is the fuel itself, is also cold and this sub zero / freezing temperature fuel is sprayed into the cold engine’s combustion chamber, where it mixes with the cold air drawn thru turbocharger.
Additional problems will result from fact that a cold starting diesel engine needs to reach at least two hundred (200) rpm to develop a four hundred (400) psi compression pressure to sufficiently compress the air to fuel mixture, and thus, resulting in combustion.
These two problems will result in the diesel fuel being sprayed into the combustion chamber, and it will condense on the cold surfaces of the cylinder liners or cylinder block. This liquid fuel will seep through the piston rings, and fall into the engine’s crankcase, diluting the lubricating oil in the process.
Two simple devices can be used to reduce the possibility that these conditions occur. One is by the use of battery heaters and glow plugs. No one device can be used. Usually a combination of several devices will provide an overall efficient starting process.
The efficiency of a battery drops as its temperature drops. A battery that is fully charged at 26 degrees C (80 degrees F) will have its starting capacity drop to approximately forty six percent (46%) available power at 17.7 degrees C below 0 (0 degrees F). Additionally, at this temperature, the engine will be approximately two and a half (2.5) times harder to start at -17.7 C (0 F) degrees due to thicker oil and resistance to movement of internal moving parts. This gets worst at lower temperatures are experienced.
To solve this, one of two common devices is used to heat the battery. One is a padded silicone covered, acid resistant rubber hot pad heater. This operates off of 110/120V and comes in various wattages. The power range can be 60W to 500W, and this can be used to heat the batteries, engine oil pan, fuel tank, hydraulic tank, and the water tank.
The other device that is typically used in conjunction with the hot pad is the glow plug. This is an internally fixed low voltage heating element that is fitted directly into the combustion chamber. When this is switched on, it can take up to two minutes to heat up, however, by that time it has reached approximately 700 degrees C (1652 degrees F) and the combustion chamber is hot enough to prevent the condensing of the diesel fuel, and thus, ignition is guaranteed.
Ontario Parts Hotline is a premium aftermarket provider of John Deere Parts and 4020 John Deere Parts
The hard starting problems of diesel engines in below zero / freezing temperatures are caused by two factors. One is the initial cold air being drawn into the turbocharger and compressed into the engine’s cylinder head. The second is the fuel itself, is also cold and this sub zero / freezing temperature fuel is sprayed into the cold engine’s combustion chamber, where it mixes with the cold air drawn thru turbocharger.
Additional problems will result from fact that a cold starting diesel engine needs to reach at least two hundred (200) rpm to develop a four hundred (400) psi compression pressure to sufficiently compress the air to fuel mixture, and thus, resulting in combustion.
These two problems will result in the diesel fuel being sprayed into the combustion chamber, and it will condense on the cold surfaces of the cylinder liners or cylinder block. This liquid fuel will seep through the piston rings, and fall into the engine’s crankcase, diluting the lubricating oil in the process.
Two simple devices can be used to reduce the possibility that these conditions occur. One is by the use of battery heaters and glow plugs. No one device can be used. Usually a combination of several devices will provide an overall efficient starting process.
The efficiency of a battery drops as its temperature drops. A battery that is fully charged at 26 degrees C (80 degrees F) will have its starting capacity drop to approximately forty six percent (46%) available power at 17.7 degrees C below 0 (0 degrees F). Additionally, at this temperature, the engine will be approximately two and a half (2.5) times harder to start at -17.7 C (0 F) degrees due to thicker oil and resistance to movement of internal moving parts. This gets worst at lower temperatures are experienced.
To solve this, one of two common devices is used to heat the battery. One is a padded silicone covered, acid resistant rubber hot pad heater. This operates off of 110/120V and comes in various wattages. The power range can be 60W to 500W, and this can be used to heat the batteries, engine oil pan, fuel tank, hydraulic tank, and the water tank.
The other device that is typically used in conjunction with the hot pad is the glow plug. This is an internally fixed low voltage heating element that is fitted directly into the combustion chamber. When this is switched on, it can take up to two minutes to heat up, however, by that time it has reached approximately 700 degrees C (1652 degrees F) and the combustion chamber is hot enough to prevent the condensing of the diesel fuel, and thus, ignition is guaranteed.
Ontario Parts Hotline is a premium aftermarket provider of John Deere Parts and 4020 John Deere Parts
Signs of tractor Water Pump Problems and How to Correct It
A tractor cooling system comprises of several components, including a water pump and a radiator. These two major components of the tractor’s cooling system differ is its functions, breakage problems, and corrective and preventive maintenance procedures.
A basic tractor water pump is made up of three major parts, and a series of smaller minor parts.
The major three components of the water pump are the outside housing, the central shaft, and the water impeller. One end of the impeller shaft fits into the circular impeller, and the other end of the impeller fits into the water pump housing. The impeller shat fits into the housing via a sealed bearing and a copper bushing called a shaft slinger.
A section of the impeller shaft protrudes from the housing, and onto that is fitted a single or double groove pulley. A key is used to ensure that the pulley does not slip o the shaft.
The continuous rotation of the water pump shaft, which turns the impeller, pulley and fan blades, will wear out over time due to normal wear and tear. The sealed bearing will damage over time, as are the copper bushings. The impeller can corrode overt time by the continuous cavitations of the coolant fluid passing through it.
These damaged bearings and bushings, will give rise to slight vibrations initially, and then to small leakage of coolant through the bearings area. At this time, its advisable to change the water pump .
In older Allis Chalmers, Case, IH, John Deere, Massey Ferguson, Ford, New Holland, Kubota, Deutz, David Brown, Farmall tractors, the water pump pulley is attached to the fan hub. If the leaking water pump is not changed, then there is the risk of the bearing completely breaking apart. This complete braking up will render the pump pulley and hub to rotate in a hap hazard fashion, and the fan blades can actually cut into the radiator, producing additional failed components i.e., the radiator and the damaged fan blades.
In newer tractors the fan blades are electrically driven, and is separate from the water pump.
Regular inspection of the pump can prevent this, or better yet, the pump should be changed after a certain amount of operational hours. A leaking water pump can be quickly repaired using a water pump repair kit. The repair kit components can include an impeller, impeller shaft, gasket, bushings, bearings, and retailer clips.
If the housing of the pump is damaged, then the entire water pump needs to be changed.
On some water pump housings are stamped/casted a number. Get that number and call your parts supplier.
Ontario Parts Hotline is a premium provider of John Deere Parts and Ford Tractor Radiator
A basic tractor water pump is made up of three major parts, and a series of smaller minor parts.
The major three components of the water pump are the outside housing, the central shaft, and the water impeller. One end of the impeller shaft fits into the circular impeller, and the other end of the impeller fits into the water pump housing. The impeller shat fits into the housing via a sealed bearing and a copper bushing called a shaft slinger.
A section of the impeller shaft protrudes from the housing, and onto that is fitted a single or double groove pulley. A key is used to ensure that the pulley does not slip o the shaft.
The continuous rotation of the water pump shaft, which turns the impeller, pulley and fan blades, will wear out over time due to normal wear and tear. The sealed bearing will damage over time, as are the copper bushings. The impeller can corrode overt time by the continuous cavitations of the coolant fluid passing through it.
These damaged bearings and bushings, will give rise to slight vibrations initially, and then to small leakage of coolant through the bearings area. At this time, its advisable to change the water pump .
In older Allis Chalmers, Case, IH, John Deere, Massey Ferguson, Ford, New Holland, Kubota, Deutz, David Brown, Farmall tractors, the water pump pulley is attached to the fan hub. If the leaking water pump is not changed, then there is the risk of the bearing completely breaking apart. This complete braking up will render the pump pulley and hub to rotate in a hap hazard fashion, and the fan blades can actually cut into the radiator, producing additional failed components i.e., the radiator and the damaged fan blades.
In newer tractors the fan blades are electrically driven, and is separate from the water pump.
Regular inspection of the pump can prevent this, or better yet, the pump should be changed after a certain amount of operational hours. A leaking water pump can be quickly repaired using a water pump repair kit. The repair kit components can include an impeller, impeller shaft, gasket, bushings, bearings, and retailer clips.
If the housing of the pump is damaged, then the entire water pump needs to be changed.
On some water pump housings are stamped/casted a number. Get that number and call your parts supplier.
Ontario Parts Hotline is a premium provider of John Deere Parts and Ford Tractor Radiator
Subscribe to:
Posts (Atom)